Page tree

Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

  1. You will need a separate computer, Windows or Mac, to update your NADAC PLAYER firmware.
    Make sure your NADAC PLAYER is connected on this computer, and your computer is set to use an automatic IP address or DHCP.
    Otherwise you may not be able to send the firmware file into NADAC PLAYER.
    See this page to see how-to configure your computer with an automatic IP address. 
      
  2. Download the latest NADAC PLAYER firmware:
    Firmware_3.69.0_3244934718.NADAC-PLAYER


  3. Make sure that the downloaded firmware file is on a computer that is on the same network as your NADAC PLAYER. 
  4. Restart your NADAC PLAYER in Maintenance mode :
    • Long press the NADAC PLAYER rotary button to access the menu.
    • Select Exit and short press the NADAC PLAYER rotary button. 
    • Select Maintenance and short press the NADAC PLAYER rotary button. 
    • Confirm the reboot to maintenance mode by clicking on Yes

      Tip

      If your NADAC PLAYER is shut down, you can also press & hold the Volume button and push the Power button to have it start in Maintenance mode.
      Keep the Volume button pressed until the yellow caution border display appears on its display.

  5. Wait until NADAC PLAYER is fully booted (the progress bar says “Ready”)
    Please note its IP address, displayed on NADAC PLAYER display.
  6. Check your Maintenance version : please have a look at your NADAC PLAYER display.
    You will see your Maintenance mode version : V0xx
     

    Warning

    At the Firmware update users could be warned that their Maintenance Mode is not up to date. In such case it is important to follow the Maintenance Mode update procedure prior to updating to the latest Firmware.

    If your Maintenance version is below V037, you will first need to update the Maintenance mode before applying the firmware update.
    Please follow the Maintenance Mode update instructions on this page.

  7. Start your default web browser (Merging recommends Google Chrome or Apple Safari), and enter the following address:

    Panel
    http://yourNADACPLAYERIPADDRESS:8080

    In the example below, the NADAC PLAYER IP address is 10.0.0.32.
    This address is then automatically translated and redirects you to the firmware update page.


     

  8. Click on “Select File” and choose the firmware file (.NADACPLAYER) that you have previously downloaded on your disk and click on Open.
    Warning: Before clicking on Update make sure that the file is fully loaded and indicated e.g. Firmware_3.5.0_31226.NADACPLAYER.
    Do not update your NADAC PLAYER with a .NADAC firmware (e.g. Firmware_3.5.0_31226.NADAC not good)


     
  9. Click on Update Device.
    The firmware will be uploaded into the NADAC PLAYER, you can see progress indicated at the bottom of your Browser Page and on the NADAC PLAYER screen.
    The NADAC PLAYER power button will also blink red during the update process.

     

    Warning

    During update do not update or refresh your browser (F5), until the process is completed. The Firmware update should take from 3 to 5 minutes. 

    Do not perform any other installation during the firmware upgrade.

    Do not shutdown the NADAC PLAYER during the update. 

     

     
  10. Wait until the webpage says “Update successful!” and the NADAC PLAYER screen displays Please Shutdown”.
         
     

  11. Shutdown your NADAC PLAYER after the Firmware update by clicking on the "Reboot device" button in the web page, it will restart automatically afterwards.

  12. You can verify the firmware version installed by going into the NADAC PLAYER Setup menu and selecting Info. The firmware version and date will be displayed.

    Info

    If you had to change your computer IP address for the firmware update, you may now set it again to your preferred IP address.

...