Page tree

Versions Compared


  • This line was added.
  • This line was removed.
  • Formatting was changed.


  1. Right click on the Network icon in the Windows Taskbar.
  2. Select: Open Network and Sharing Center

  3. Click on: Change Adapter Settings on the left of the pane.

  4. Right-click the Merging Technologies PCIe 8257 RAVENNA Network Card and select Properties:
    (same procedure applies with any other network adapter)

  5. Select Internet Protocol Version 4 (TCP/IP) and Click on Properties:

  6. Click on the Use the following IP address: radio button and enter (the Cisco SG350 switch has a factory default IP address of
    Click on the OK button to accept the settings and close the dialog. 

    1. Note: if the switch cannot be accessed at the address, it could be that a DHCP is present, in which case, open MTDiscovery and check if the switch appears with the name "SwitchABCDEF" with the last digits being its MAC address.
  7. Open a browser and type in the address bar.
    Default user name: "cisco" - password: "cisco".
    Click on the Log in button .

  8. After the login prompt, you will be asked to change that default password to whatever you want.
    It is a required step and the first one into securing you're router/switch, it is also a one time step only.

    After the default is changed, if you wish to change it again you will have to do that in the Administration page.
    Reseting the switch to "factory defaults" will also ask you to do this step again.


  9. Make sure the switch is running firmware or above.
    Click on the About button on top right of the screen.

    If you have to update the firmware, refer to Cisco 350, 350X, and 550X Series Managed Switches Administration Guide -  Firmware Operations section.
    Click here to access Cisco documentation website

  10. The Administration page will now load and you can start configuring your switch.

  11. Download the latest configuration file for your Cisco SG350 switch model :


    Cisco SG350-10
    Cisco SG350-10 - Dual VLAN (Port 1 to 5 : Regular network. Port 6 to 10 : RAVENNA/AES67)
    Cisco SG350-10 - ACL Port 8 (Port 8 configured to filter all Multicast Streams, allowing to connect a non-RAVENNA/AES67 Network.   Eg. Connect directly an AP WIFI for some remote control purpose (tablet, smartphone), connect your Internet router.)

    The Merging RAVENNA configuration file will auto-configure various settings /protocols to optimize the RAVENNA / AES67 network, and also sets the definitive fixed IP address of the switch:

  12. Go into "Administration" then click "File Management" to expand, then click "File Operations" to open its pane.

  13. Now select
    Operation Type : Update File
    Destination File Type : Startup Configuration
    Copy Method : HTTP/HTTPS


  14. Then click Choose File and a new window will pop up.
    In the Choose File window point to the downloaded configuration file  location, select it and click Open.

  15. Then click Apply for it to load your configuration file into the STARTUP CONFIG.

  16. The switch will send a notification that the operation has been completed.

  17. You must now restart the switch for the changes to apply.
    Click Administration > Reboot
    Select Immediate and click on Reboot button.
    Note that the device might take some time to reboot.

  18. In the Network Connections window (see steps  3. 4. and 5. above), right-click the Merging Technologies PCIe 8257 RAVENNA Network Card and select Properties.
    Select the Obtain an IP address automatically radio button and also select Obtain DNS server address automatically, click on OK.
  19. The switch is now configured and ready to use, and the Merging RAVENNA Network Card should have auto-configured itself with an IP in the 169.254.x.x range. 
    You can verify this by opening a browser and typing in the address bar, and log in.